EU Regulation 2025/40 (PPWR) applies from 12 August 2026 across all 27 Member States. Each packaging type placed on the EU market needs an EU Declaration of Conformity drawn up by its manufacturer (Article 15(2), Annex VIII). The sum of lead, cadmium, mercury and hexavalent chromium in packaging may not exceed 100 mg/kg (Article 5(4)). PFAS above set concentration thresholds in food-contact packaging are banned. Recyclability grades and recycled-content minimums apply from 1 January 2030 at the earliest. No notified body required: self-assessment under Module A.
The Packaging and Packaging Waste Regulation (EU) 2025/40 entered into force on 11 February 2025 and applies across all 27 Member States from 12 August 2026. From that date, each packaging type placed on the EU market needs an EU Declaration of Conformity drawn up by its manufacturer, the sum of lead, cadmium, mercury and hexavalent chromium in packaging may not exceed 100 mg/kg (Article 5(4)), PFAS above set concentration thresholds in food-contact packaging is banned, and, according to the Commission, the general recyclability requirement of Article 6(1) applies, assessed against the criteria of the previous Directive 94/62/EC until the design-for-recycling rules take over (guidance document C/2026/3084, section 6). This guide walks through what changes, when, and what manufacturers need in their technical file.
What is the PPWR?
The Packaging and Packaging Waste Regulation, formally Regulation (EU) 2025/40, is the directly applicable EU law replacing Directive 94/62/EC. It harmonises packaging rules across the single market, covers all packaging types and all economic operators in the supply chain, and shifts compliance from national transposition to one common legal text. Unlike a directive, no national implementation is required: obligations bite the day they apply.
PPWR Timeline: Key Dates Through 2040
The regulation rolls out in waves. The August 2026 date is widely cited as "PPWR D-Day" but it is not the moment every requirement triggers. Two Commission delegated acts have already been adopted: Delegated Decision (EU) 2026/429, which exempts certain economic operators that use pallet wrappings and straps from the re-use requirements for those formats, and Delegated Decision (EU) 2026/1948 on crystal glass packaging. The implementing acts on the harmonised label, due by 12 August 2026 under Article 12(6) and (7), had not been published as of 29 October 2026. Further delegated and implementing acts are still to come, and several of them determine when the obligations below actually apply.
| Date | Obligation | Who is affected |
|---|---|---|
| 11 February 2025 | Entry into force | All operators (no obligations yet) |
| 12 August 2026 | General application: DoC, heavy-metal limit of 100 mg/kg (Article 5(4)), PFAS ban (food contact), recyclability under PPWD criteria (Commission reading of Article 6(1), C/2026/3084, section 6), ban on double walls/false bottoms (Article 10(2) on the wording of the Regulation; the Commission reads all of Article 10 as applying from 1 January 2030) | Manufacturers, importers, distributors, fulfilment service providers |
| 1 January 2028 | Commission deadline to adopt delegated acts on Design for Recycling criteria (Article 6(4)) | Commission, then industry |
| 12 August 2028 at the earliest | Harmonised material-composition label (Article 12(1)), or 24 months after the implementing acts under Article 12(6) or (7) if that is later; a QR code or other data carrier stays optional, except for reusable packaging (12 February 2029 at the earliest, Article 12(2)) | Manufacturers, importers |
| 1 January 2030 | Recyclability grades A, B or C mandatory, minimum recycled content for plastic packaging and 50% empty-space cap for transport, grouped and e-commerce packaging, each later if the relevant delegated or implementing act comes late (Articles 6(3), 7(1) and 24(1)); weight-and-volume minimisation (Article 10(1)); restricted packaging formats, mostly single-use plastic (Annex V) | All packaging on the EU market |
| 1 January 2035 | "Recyclable in practice and at scale" test applies (later if the implementing act comes late, Article 6(2)) | All packaging |
| 1 January 2038 | Only grade A or B accepted | All packaging |
| 1 January 2040 | Higher minimum recycled content in any plastic part of packaging, calculated as an average per manufacturing plant and year: 50% for contact-sensitive PET packaging and 25% for contact-sensitive packaging in other plastics (single-use plastic beverage bottles excluded from both), 65% for single-use plastic beverage bottles, 65% for other plastic packaging (Article 7(2)) | Packaging with plastic parts |
Scope: What Counts as Packaging?
PPWR covers sales packaging (the unit consumers buy), grouped packaging (multipacks), and transport packaging including e-commerce shipping boxes. Service packaging, such as cups handed over at point of sale, falls in scope too. The regulation makes no distinction by material: plastic, paper, glass, metal, wood and composites are all caught. Reusable packaging follows a separate track with its own targets per sector, notably beverage, transport and grouped packaging used B2B.
The legal text also widens the chain of responsibility. Importers and distributors take on manufacturer obligations under Article 21 when they place packaging on the market under their own name or trademark, or modify it in a way that could affect compliance. Fulfilment service providers (Amazon-style warehouses) must ensure that their warehousing, handling, packing, addressing and dispatching do not jeopardise the packaging's compliance (Article 20). Distributors carry a lighter due-diligence duty but cannot turn a blind eye to non-compliant stock moving through their channels.
The reach of the regulation extends to packaging used inside the EU even when the brand behind it sits outside the bloc. A non-EU brand shipping into a German Amazon warehouse for onward distribution to French consumers is squarely in scope, and the legal anchor is whichever entity first places the packaging on the Union market. This is why supplier contracts signed in 2026 increasingly carry PPWR warranties, audit rights, and indemnification clauses tied to the August deadline.
Obligations Applying from 12 August 2026
Three operational requirements bite on D-Day. None of them gets a stock-exhaustion period: what counts is the date the packaging is placed on the market, not the date it was produced (see the first question in the FAQ below).
1. EU Declaration of Conformity (Article 39)
Every packaging type placed on the market needs a written EU Declaration of Conformity drawn up under Annex VIII. The manufacturer signs it, and it rests on the underlying technical documentation prepared under Annex VII (Module A internal production control). Documentation retention runs five years for single-use packaging and ten years for reusable packaging. A separate guide on the Declaration of Conformity details exactly what goes into Annex VIII and how to operationalise it across SKUs.
For the technical file itself (Annex VII), see the PPWR Annex VII technical documentation guide, which covers the evidence required for each packaging type, the 5-year and 10-year retention obligations by packaging category, and the 10-day market surveillance authority access rule.
2. Heavy-Metal Limit and PFAS Ban in Food-Contact Packaging (Article 5)
The heavy-metal limit covers all packaging, whatever it contains: the sum of the concentrations of lead, cadmium, mercury and hexavalent chromium resulting from substances present in packaging or packaging components may not exceed 100 mg/kg (Article 5(4), applicable from 12 August 2026 under Article 71). Two derogations adopted under the previous Directive remain in force until the Commission repeals them by delegated acts under Article 5(8): Decision 2001/171/EC for glass packaging and Decision 2009/292/EC for plastic crates and plastic pallets (Article 70(3)). Commission Delegated Decision (EU) 2026/1948, published in the Official Journal on 28 October 2026 and in force since 29 October 2026, amends Decision 2001/171/EC to add a time-limited derogation for crystal glass packaging: it may exceed the limit until 31 December 2029, but crystal glass packaging containing lead may only be manufactured until 31 December 2028. The derogation is conditional on a dealkalisation treatment limiting lead release into the contents, a permanent marking identifying the crystal glass producer, information to end users on returning the packaging for recycling free of charge, and a closed and controlled loop that brings returned packaging back to the producer it came from.
The PFAS ban concerns food-contact packaging only. Packaging in contact with food may not contain per- and polyfluoroalkyl substances above three thresholds: 25 ppb for any individual non-polymeric PFAS, 250 ppb for the sum of non-polymeric PFAS via targeted analysis, and 50 ppm for total PFAS including polymeric. Compliance with both the heavy-metal limit and the PFAS thresholds is demonstrated in the Annex VII technical documentation (Article 5(6)), which includes the test reports (Annex VII, point 2(f)). See the dedicated article on the PPWR PFAS ban in food-contact packaging: thresholds, testing and supplier proof for the analytical chemistry side.
3. Packaging Minimisation Principle
On the wording of the Regulation, the narrower minimisation rule bites from August 2026: under Article 10(2), packaging may not use double walls, false bottoms or other unnecessary layers designed only to increase its perceived volume. The broader duty to reduce weight and volume to the minimum necessary for functionality (Article 10(1)) applies only from 1 January 2030, the earliest date for the 50% empty-space cap (Article 24(1)). The Commission reads both paragraphs of Article 10 as applying from 1 January 2030, with the minimisation requirement of Directive 94/62/EC and its standard EN 13428:2004 remaining in effect until the end of 2029 under Article 70(1)(b) (guidance document C/2026/3084, section 10). E-commerce is the most scrutinised vertical here, with national authorities likely to use the 2030 empty-space ratio as a forward-looking benchmark. The e-commerce empty-space guide covers right-sizing strategies.
What Changes in 2028: Harmonised Labelling
From 12 August 2028, or 24 months after the Commission's implementing acts under Article 12(6) or (7) enter into force if that is later, packaging placed on the EU market must carry a harmonised, pictogram-based label on its material composition to facilitate consumer sorting (Article 12(1)). Transport packaging is excluded, except e-commerce packaging, and so is packaging under a deposit and return system. Both implementing acts were due by 12 August 2026 (Article 12(6) and (7), first subparagraph) and neither had been published as of 29 October 2026, so in practice the label will be due 24 months after the later of them enters into force. Reusable packaging needs its own label from 12 February 2029 at the earliest (Article 12(2)). According to the Commission, Member States cannot keep their national labels next to the EU label once it applies (guidance document C/2026/3084, section 13); in our reading, this covers labels such as French Triman or Italian environmental labelling. A QR code or other data carrier is optional alongside the label (Article 12(1)); it becomes mandatory only for reusable packaging, to give information on reusability (Article 12(2)).
What Changes in 2030: The Real Market-Access Cliff
January 2030 is the date non-compliant packaging actually loses market access. Three obligations stack on the same day:
- Recyclability grades: packaging must achieve grade A, B or C under Design for Recycling criteria (delegated acts due by 1 January 2028); the obligation applies from 1 January 2030 or 24 months after those acts enter into force, whichever is the latest (Article 6(3)). Packaging that does not reach grade C cannot be placed on the market.
- Recycled content for plastic packaging: minimum recycled content thresholds vary by packaging category (contact-sensitive vs. non-sensitive, PET vs. other plastics), with stricter targets for 2040; the 2030 date moves to 3 years after the implementing act on the calculation methodology if that is later (Article 7(1)).
- Empty-space cap: grouped, transport and e-commerce packaging cannot exceed 50% empty space. Filler material (paper, air pillows, bubble wrap) counts as empty space, not as product volume. The 2030 date moves to 3 years after the implementing act on the calculation method if that is later (Article 24(1)).
The packaging formats and uses listed in Annex V, mostly single-use plastic, are banned from 1 January 2030 (Article 25(1)), including most plastic carrier bags below 15 microns, single-portion HORECA condiment sachets, and certain hotel toiletry miniatures.
PPWR and the Digital Product Passport
PPWR does not, on its face, mandate a full Digital Product Passport in the ESPR sense. What it does mandate is a Declaration of Conformity from 2026; a data carrier on packaging is optional alongside the harmonised label, and mandatory only for reusable packaging from 12 February 2029 at the earliest (Article 12(1) and (2)). Both interoperate naturally with DPP infrastructure. For manufacturers already preparing DPPs for products under the Ecodesign for Sustainable Products Regulation (batteries February 2027 under Regulation (EU) 2023/1542; textiles under a forthcoming ESPR delegated act; construction products under the revised Construction Products Regulation), extending the same data model to packaging avoids duplicate work. The PPWR + DPP integration guide covers how a single passport architecture can serve both regimes, and the battery passport guide shows how a sister regulation (EU 2023/1542) treats the same data carrier question.
Building a Compliance Roadmap
For most operators the first task is mapping which packaging types in their portfolio are caught by which obligation. A simple matrix: rows for SKU families, columns for the August 2026 obligations (DoC, heavy-metal limit, PFAS, the Article 10(2) ban on double walls and false bottoms), then for 2028 (label) and 2030 (recyclability grade, recycled content, empty space). Each cell flags status, owner, and deadline. The exercise sounds bureaucratic, but it forces the conversation between procurement, packaging design, regulatory affairs, and supply chain that PPWR was specifically written to provoke.
A pragmatic sequencing for a mid-sized brand owner, as of 29 October 2026:
- Should already be in place, since the obligations behind it apply from 12 August 2026; if not, do it now: heavy-metal testing across the packaging range (Article 5(4)), PFAS testing on all food-contact references, supplier questionnaires returned, technical files drafted.
- Should already be in place as well; if not, do it now: Declaration of Conformity signed for every SKU placed on the market, retention infrastructure ready.
- 2027: Recyclability assessment, recycled content roadmap, label redesign workstream kicked off.
- Q2 2028: Harmonised label rolled out, timed to the date that actually applies (12 August 2028 at the earliest, or 24 months after the labelling implementing acts).
- 2029: Empty-space ratio audit completed, carton portfolio rationalised, reusability targets translated into specific product lines.
Frequently Asked Questions
Does PPWR apply to packaging already in stock on 12 August 2026?
It depends on what “in stock” means, because the trigger is placing on the market, not manufacturing. Packaging first made available on the Union market from 12 August 2026 must comply, regardless of when it was produced, so goods sitting in your own warehouse awaiting first sale are caught. Packaging that was already placed on the market before the relevant requirement applies and sits in distributors’ stock, including retailers and wholesalers, does not have to meet the sustainability and labelling requirements (recital 14).
Is a notified body required for PPWR conformity assessment?
No. PPWR uses internal production control (Module A under Annex VII). The manufacturer self-assesses, signs the Declaration of Conformity, and keeps the technical file. Authorities can audit at any time. Missing or incomplete documentation is a formal non-compliance: if it persists, the Member State must prohibit the packaging from being made available or have it recalled or withdrawn (Article 62(1) and (2)), and penalties are set by national law (Article 68).
What is the difference between PPWR and the previous Packaging Directive?
The Packaging Directive 94/62/EC required national transposition and left interpretation room to each Member State. PPWR is a regulation, meaning the same text applies in all 27 countries from the same date, with no transposition. Obligations are also more granular and quantitative, with recyclability grades, PFAS limits, and recycled-content percentages set directly in the regulation.
Do non-EU manufacturers need to comply with PPWR?
Indirectly, yes. The EU importer placing the packaging on the market is legally responsible, but in practice non-EU suppliers must hand over the technical documentation needed for the Declaration of Conformity, or the importer will not be able to ship. Authorised representatives under Article 17 give non-EU manufacturers a contact point inside the Union, but the technical documentation cannot be delegated to them.
What are the PPWR labelling requirements from 2028?
From 12 August 2028, or 24 months after the labelling implementing acts under Article 12(6) or (7) enter into force if that is later, packaging placed on the EU market must carry a harmonised, pictogram-based label on its material composition (Article 12(1)); transport packaging other than e-commerce packaging, and packaging under a deposit and return system, are excluded. The pictograms and specifications come from Commission implementing acts (Article 12(6)), not yet published as of 29 October 2026. Reusable packaging needs a separate label from 12 February 2029 at the earliest (Article 12(2)). A QR code or other data carrier is optional alongside the label (Article 12(1)) and mandatory only for reusable packaging (Article 12(2)). According to the Commission, Member States cannot keep national labels next to the EU label (C/2026/3084, section 13), which in our reading includes France’s Triman or Italy’s environmental label. Where a data carrier is used, it can connect to the packaging DPP infrastructure described in the PPWR + DPP integration framework.
What penalties apply for PPWR non-compliance?
PPWR Article 68 requires each Member State to establish penalties that are "effective, proportionate and dissuasive." The regulation does not set EU-wide fine amounts directly: enforcement is national. For formal non-compliance, such as a missing or incorrectly drawn up Declaration of Conformity or missing, incomplete or erroneous technical documentation (Article 62(1), points (a) to (f)), the Member State first requires the operator to put an end to it; if it persists, the Member State must take all appropriate measures to prohibit the packaging from being made available on the market or to have it recalled or withdrawn (Article 62(2)). Where the non-compliance concerns excessive packaging or restricted formats, re-use and refill obligations, re-use targets, recyclability or recycled content (Article 62(1), points (g) to (n)) and persists, the national penalties laid down under Article 68 apply (Article 62(3)). Packaging that presents a risk to the environment or human health follows a separate procedure: market surveillance authorities evaluate it, require corrective measures within a set period and, if the operator does not act or the non-compliance persists, take provisional measures to prohibit its making available, withdraw it or recall it (Article 58(1) and (5)). Packaging entering the Union market can also be stopped before release for free circulation: under Articles 25 to 28 of Regulation (EU) 2019/1020, which apply to products covered by Union law (Article 2(2) of that Regulation), the designated customs or market surveillance authorities suspend release where the required documentation, marking or labelling is missing or there is cause to believe the product does not comply (Article 26(1)), and refuse release where the market surveillance authorities conclude that it does not comply (Article 28(2)). Market surveillance authorities pass their Article 58(5) measures on to those authorities for their risk analysis (Article 61 PPWR).
Does PPWR apply to packaging of non-food products?
Yes. PPWR scope is not limited to food packaging: it covers all packaging types and all materials (plastic, paper, glass, metal, wood) regardless of what is inside. The Article 5 PFAS ban is the only obligation that is explicitly restricted to food-contact packaging. All other PPWR obligations (Declaration of Conformity, minimisation, recyclability grades from 2030, labelling from 2028) apply to packaging of non-food products on exactly the same timeline.
What is the difference between PPWR and PPWD for importers?
Under the Packaging and Packaging Waste Directive 94/62/EC (PPWD), each Member State transposed rules differently, creating 27 national frameworks. PPWR (Regulation 2025/40) applies identically in all Member States from the same date, with no transposition step. For importers, this means one set of compliance documentation covers the entire EU single market. Article 21 assigns manufacturer responsibilities to the EU importer when the importer places packaging on the market under its own name or trademark, or modifies it in a way that could affect compliance. Article 17 allows a non-EU manufacturer to designate an authorised representative inside the Union. That mandate cannot include drawing up the technical documentation, which stays with the manufacturer.